Infranoto
Back to blog

How to Do a Job Hazard Analysis (JHA/JSA): A Step-by-Step Guide With a Worked Example

By Infranoto

Ask to see the job safety analysis for a task on your floor, and there's a good chance you'll get a form that was copied from another site, lists "pinch points" and "be aware of surroundings," and was signed by the whole crew in under a minute. It satisfies the audit checklist. It doesn't tell anyone what could actually hurt them on this job, or what's been done about it.

A good analysis is one of the most useful documents in a safety program. It turns a job your crew does every day into a specific list of what can go wrong and what stops it. It also doesn't take specialized software or a consultant to do well. Here's how to build one that people will use.

What a job hazard analysis is

OSHA's guide, Job Hazard Analysis (OSHA 3071), defines it as a technique that focuses on job tasks as a way to identify hazards before they occur, looking at the relationship between the worker, the task, the tools, and the work environment.

You'll see it called a JHA, a JSA (job safety analysis), or an AHA (activity hazard analysis). OSHA uses "job hazard analysis," many companies say "JSA," and in everyday use they mean the same thing: break a job into steps, identify the hazards in each step, and put controls in place.

It's easy to confuse with a few related tools, so here's how they fit together:

ToolWhat it answersWhen it happens
Job hazard analysisWhat can hurt someone at each step of this job, and what controls it?Before the job, then reviewed over time
Pre-task planWhat's different about doing this job here, today?At the start of the task or shift
Toolbox talkWhat's the one hazard this crew should focus on right now?Pre-shift, five to ten minutes
Permit-to-workIs this specific high-hazard job authorized, under these conditions, for this time window?Before hot work, confined space entry, and similar jobs

Is a JHA required?

Federal OSHA doesn't have a general standard requiring a JHA for every job. But several rules come close, and you may need one anyway:

  • PPE hazard assessment. 29 CFR 1910.132(d) requires employers to assess the workplace for hazards that call for PPE and to verify that assessment with a written certification. A JHA doesn't replace the certification, but it gives you much of the underlying work.
  • Job briefings in utility work. 29 CFR 1910.269(c) requires job briefings covering hazards, procedures, energy source controls, and PPE on covered electric power work.
  • Customers and insurers. Many prequalification programs and contracts ask for task-level hazard analyses, whether or not a regulation does.

State-plan states can have their own requirements, so check yours. And whatever the rule says, the practical reason to do one is simple: it's how you find hazards before an injury finds them for you.

Step 1: Pick the right jobs first

You can't analyze everything at once, so start where it matters most. OSHA says priority should go to:

  • Jobs with the highest injury or illness rates
  • Jobs with the potential to cause severe or disabling injuries, even with no history of accidents
  • Jobs where one simple human error could lead to a severe injury
  • Jobs that are new to your operation or have changed
  • Jobs complex enough to require written instructions

The second item is the one most programs miss. If you rank jobs only by past injury counts, a task that produces lots of minor cuts will outrank a task that has never hurt anyone but could kill someone the first time it goes wrong. Non-routine work deserves particular attention: clearing jams, changeovers, maintenance, and startup after a shutdown.

Your own data can help here. Pull your incidents, first aid cases, and near-miss reports, and sort them by task. OSHA treats close calls as a sign that existing controls may not be adequate, and it recommends reviewing that history with your employees before you begin.

Step 2: Bring in the people who do the job

A JHA written in the office describes how the job is supposed to work. The crew knows how it actually works. Include at least one experienced worker from start to finish, and ask questions that get at the real conditions:

  • "What's the worst part of this job?"
  • "What do you do when the proper tool isn't handy?"
  • "Where have you had a close call doing this?"

Be clear about the purpose. OSHA's advice is to point out that you're evaluating the job itself, not the employee's performance.

If someone identifies a hazard that poses immediate danger along the way, don't wait for the analysis to finish. Protect people now. OSHA also advises fixing anything that's easy to correct as soon as possible, which shows the crew the process leads somewhere.

Step 3: Watch the job and write down the steps

Go to the work and watch someone do it, listing each step as they take it. Then review the list with them to catch anything you missed. A photo or short video can be useful for working through the details later.

The common mistake is getting the level of detail wrong. "Replace the motor" is too broad to reveal any hazards. "Pick up the 9/16 wrench" is so detailed that nobody will read it. As a rule of thumb, most jobs break down into about 5 to 12 steps, each starting with an action verb. If you're at 30, you're probably describing several jobs, or writing a procedure.

Record the job as it's actually performed, including workarounds. If the crew and the written procedure disagree, that's a finding, not an inconvenience.

Step 4: Identify the hazards in each step

OSHA calls this "an exercise in detective work." For each step, ask:

  1. What can go wrong?
  2. What are the consequences?
  3. How could it happen?
  4. What other factors contribute?
  5. How likely is it?

Vague entries are the most common failure of JHAs. A strong hazard description says where it happens, who is exposed, what triggers it, and what the result would be:

Weak hazard entryStrong hazard entry
Pinch pointsHand caught between the cylinder and mounting bracket while lowering the cylinder into place, causing crushed fingers
Struck-byWorker changing a cylinder in the aisle is hit by a passing forklift that can't see them behind the parked truck
Slip hazardFoot slides on hydraulic oil on the top step while climbing down from the press, causing a fall of about four feet

To help with severity and likelihood, a simple 3x3 or 5x5 risk matrix is enough to decide what gets attention first. Don't let the scoring turn into the main event. Pay close attention to any step where the hazard could cause a fatality or permanent injury, even when the odds look low.

Step 5: Choose controls, starting at the top

Work down the hierarchy of controls for each hazard: elimination, substitution, engineering controls, administrative controls, then PPE.

If a JHA is mostly "wear gloves" and "use caution," it's documenting the hazards rather than controlling them. OSHA's guide makes this point with a worker clearing a snag near a rotating pulley: experience has shown that training is not very effective in hazard control when triggering events happen quickly, because humans can react only so quickly.

Two tests help:

  • Could someone do this exact control, and could you verify they did? "Stay alert" fails. "Set the parking brake and lower the forks to the floor" passes.
  • Is the control actually available? If the JHA calls for a cylinder cart and the site has one, shared across three buildings, the crew will carry the cylinder.

Anything that needs a purchase or a repair should become a corrective action with an owner and a due date. A JHA can't list a control that doesn't exist yet as if it were in place.

A worked example: changing a propane cylinder on a forklift

Here's a shortened example for a common job at manufacturing and logistics sites. It's for illustration only. Build yours around your equipment, the manufacturer's instructions, and the OSHA standards that apply to your operation.

Job stepWhat can go wrongControls
1. Park in the designated change area, lower forks, set brakeWorker struck by other traffic; propane released near an ignition sourceMarked change area away from traffic, ignition sources, and drains; no smoking or open flames
2. Close the cylinder valve, run the engine until it stops, turn off the keyFuel left in the line releases during disconnectFollow the valve-closed, run-dry sequence every time, with the steps posted at the change area
3. Disconnect the fuel couplingEscaping liquid propane causes cold burns to hands or eyesGloves rated for LP handling and safety glasses, stored at the change area
4. Release the bracket and lift the empty cylinder offBack strain from an awkward lift at truck height; cylinder dropped on footLift assist or cylinder cart; change area set up to minimize carrying; safety-toe footwear
5. Move the empty to the storage cage and bring back a full oneFull cylinder (often around 60 pounds) dropped or carried over a long distance; damaged valveCart for all moves; storage cage located close to the change area; inspect the full cylinder before use
6. Mount the full cylinder and secure the bracketFingers pinched at the bracket; unsecured cylinder falls during travelKeep hands clear of the bracket; align the locating pin; tug-test the latch before moving on
7. Connect the coupling, open the valve slowly, check for leaksLeak ignites or goes unnoticedLeak check with soap solution or an approved detector before starting the engine; remove any leaking cylinder from service and follow your site's response procedure

Look at what this table exposes. Three of the seven steps depend on a good change area and a cart. Fixing those solves more than any reminder would, and they're worth a corrective action if they don't exist. And if a site changes enough cylinders each week, the top of the hierarchy comes into play: electric forklifts eliminate this job altogether.

Step 6: Use it in the field

A JHA in a binder protects no one. To put it to work:

  • Review it with everyone who does the job, and explain the reasons behind any new steps. OSHA recommends discussing recommendations with all employees who perform the job and considering their responses carefully.
  • Have the crew review it before work begins, at the location of the job, and ask what's different today: weather, staffing, a new contractor, a nearby lift.
  • Make the sign-off mean something. A signature should mean "I read this, it matches the job, and I raised what doesn't." Ask someone to walk through the highest-risk step in their own words before anyone signs.
  • Let the crew change it. If conditions don't match the JHA, the right response is to stop, update the hazards and controls, and then continue. A crew who can't change the document will work around it.
  • Use it to train new employees. A good JHA is a ready-made way to teach someone a job safely.

Step 7: Keep it current

OSHA recommends reviewing JHAs periodically, because a second look often finds hazards the first one missed, even when the job hasn't changed. It's especially important to review the JHA when an illness or injury occurs on that job. Don't wait for an injury, though. Reopen a JHA whenever:

  • A root cause investigation or close call involves the task
  • Equipment, materials, the layout, or the procedure changes
  • The crew tells you the steps no longer match the work
  • It reaches your scheduled review date (annually for high-risk jobs is a reasonable starting point)

When you do revise one, train everyone affected by the change. Then look at the bigger picture. The percentage of high-risk jobs with a current JHA, and the share of controls above the PPE and administrative levels, are both useful leading indicators.

Signs your JHAs have become paperwork

  • The same hazards and controls appear on nearly every form.
  • Nobody on the crew helped write it, or could tell you where to find it.
  • Every control is training, awareness, or PPE.
  • Signatures are collected at the end of the shift, or by one person for the whole crew.
  • The last revision predates the current equipment.
  • A recent injury happened on a task whose JHA doesn't mention that hazard, and nobody updated it.

If two or three of those sound familiar, don't try to redo everything. Pick your three highest-risk jobs, and rebuild those with the crews who do them.

Each one is worth the time. A single injury can easily cost tens of thousands of dollars once indirect costs are counted, and you can estimate the figure for your own operation with the free Injury Cost Calculator. If you need a quick way to get crews talking about the hazards in a job, the free toolbox talk library has five-minute briefings on lockout/tagout, machine guarding, forklift and pedestrian safety, and more.

How Infranoto helps

A JHA is most useful when it's connected to everything else you know about the job. The Job Safety Analysis module, included on our High-Hazard plan, is built around that idea:

  • Step-by-step JSAs. Break a job into its steps and name the hazard and control for each one.
  • Crew sign-off before work begins, with every member recorded rather than one signature for the group.
  • Field deviations captured. When the job changes on the ground, the change gets recorded instead of lost.
  • Corrective actions that get verified. Controls that need a repair or a purchase can go to an owner with a due date and independent sign-off.
  • Pattern detection across sites. AI surfaces recurring hazards across incidents, near-misses, and observations, so you can see which jobs need a closer look first.

See the full feature set on the platform page, or request a demo and we'll walk through a JSA for a job like the ones your crews do every day.

The takeaway

  • Start with severity, not just injury counts. Include high-consequence jobs that have never had an incident.
  • Build it with the crew, and write down how the job is actually done.
  • Name specific hazards. "Pinch points" doesn't tell anyone what to do.
  • Aim controls up the hierarchy, and make every control something you can verify.
  • Use it at the job, with a sign-off that means something and a crew who can change it.
  • Keep it current. Reopen it after any incident, close call, or change to the work.